No products
Size: 34mm×15mm/1.34"×0.59"(approx) Digital temperature module and digital interface Built-in LEDs indicating temperatur Three Digital interfaces when the digital temperature sensor senses a key signal, LED lights on, otherwise off.
Humidity measuring range: 20%~90%RH(0-50℃temperature compensation).Temperature measuring range: 0~+50℃.Humidity measurement accuracy: ±5.0%RH.Temperature measurement accuracy: ±2.0℃.response time: <5s.low power consumption.Size:about 2.3cm x 1.2cm x 0.5cm.
Type K Type. Temperature Range:0-800°C. Thread Diameter:6mm / 0.23". Internal Insulation:Fibreglass. External Shielding:Metal Shield. Total Length:1M / 39". Fork Terminal Spacing: 3.5mm / 0.13". Size:100cm x 1cm x 1cm - 39.37inch x 0.39inch x 0.39inch.
This module is for interfacing to a microcontroller (Arduino). It uses a bright infrared (IR) LED and a phototransistor to detect the pulse in a finger.The pulse monitor works as follows:-The LED is the light side of the finger, and phototransistor on the other side of the finger, when the blood pulses, the resistance of the phototransistor will be...
When in light / daylight, the switch is closed. In Darkness the switch is off, but switches on for about one minute when it hears sound. Ideal for lighting in corridors e.t.c. The unit isn't sealed and inside components are through hole, so it's easily hackable.Operating power: LED: 25 W Filament lamp:60 W Light Sensitivity: 6LUX Sensitivity: 95...
1. onboard TTP224 capacitive touch sensor IC 4 keys2, 4 board-level status indicator3, working voltage: 2.4V-5.5V4, the module can set the output mode, the key output mode, the maximum output time and fast / low power selection5, PCB board size: 35 (mm) x29 (mm)
Voltage: 3.3V - 5VDC Detection distance: 2m--60m(adjustable) Detection Angle:35° uses LM393 Screw holes: 3mm Size of board: 31mm(length)*15mm(width) Pin definition:VCC, GND, OUT the sensor module output port OUT can be directly connected to the microcontroller IO port can, also can drive a 5v relay directly; Connection mode: VCC - VCC; GND - GND; OUT - IO
Uses LM393 comparator chip Operating Voltage 3.3V-5V PCB Size : 3.2cm * 1.4m Wiring ( 4 -wire ) 1 VCC external 3.3V-5V 2 GND External 3 DO small board digital output interfaces ( 0 and 1 ) 4 AO analog output voltage of small plate
Size: 18mm×15mm/0.71"×0.59"(approx) This switch is OFF in the resting state, when the is vibration, will a momentarily connection (ON) status, Basically there is a small coil in a metal cylinder. Vibration will make the coil short to the outer cylinder. Omnidirectional, any Angle can trigger
power supply: DC 5V/2mA. Logic 1/0: 5V/0V. Precision: 3mm. Distance range: 2cm-450cm. Working angle: ~15°. Size:4.5cm x 2cm x 1.5cm.
1. Uses groove coupler sensor. 2. Groove width:5mm. 3. Output state LED. 4. Obscured output high; unobstructed output low. 5. Driving ability, more than 15mA. 6. Operating voltage 3.3V-5V. 7. Digital switching outputs. (0 and 1) 8. A fixed bolt hole for easy installation. 9. PCB Dimensions: 3.2cm x 1.4cm.